ISO 9001:2008 certified
HomeContact UsSitemap
 

Surya Plasto Putty


Let us bring home…
Our traditional & Historical... Everlasting Delight....

“SURYA PLASTO PUTTY” interior is lime based putty with a single component product with special additives to improve the specially and better performance of the product.

SURYA PLASTO PUTTY” interior is extremely durable and highly crack-resistant when compared to the traditional cement finishes. The best quality is its breathable system where in it allows water vapor to permeate freely, so that the moisture evaporates quickly, unlike other finishes which absorbs moisture inside the wall.When lime putty is cure, it becomes as hard as a stone giving a long-lasting mineral coating.
The intrinsic features like Non-toxic, eco-friendly and application of two-coat or three-coat veneer system will make your walls left with excellent an absorption and diffusion characteristic which leads to optimal indoor & outdoor air quality. The prime quality of having higher pH in the more natural form of lime finish makes it act as an anti-bacterial surface, neutralizing the development of organic substances such as mold and fungus.

Special features:
“SURYA PLASTO PUTTY” interior is high quality water resistant putty with micro fine particles of about 300 microns. It does not require to be soaked in water for 24 hours. It can be directly applied by just mixing with water. It is an ISI certified product from an ISO 9001:20088 certified company.

When to apply: It should be applied immediately in semi-wet condition of plastering or on dry cement plastering surface, it should be applied after pre wetting the cement plaster and it should be in semi-wet condition.

Surface preparation:  Before application, clean and remove the dirt, loose particles, and foreign materials etc.and cure the surface with water. Add “SURYA PLASTO PUTTY” interior to a container containing water. Dilute 1kg “SURYA PLASTO PUTTY” interior with 750-850 ml water. For mixing use mechanical stirrer or for hand mixing use gloves (provided with the pack). It is always advisable to start with stiffer mix and gradually adds the required water. Allow the mixture to stand for 20 minutes and then apply.

Application: Apply the “SURYA PLASTO PUTTY” interior manually with putty blade or steel trowel. If you are going for 2nd coat application you must ensure that the first coat is completely dry. After the complete drying is over a mist spray curing is recommended for better result. Sanding is not required. However if there is any blade mark use very fine sand paper, i.e. 400 number water proof sand paper. To cover more thick undulation in the surface use SURYA COARSE LIME PUTTY i.e. from 1.0 mm to 10 mm thickness.

Curing: Depending upon the climatic condition, curing can be done after complete drying, i.e. 12 or 24 hours.

Setting: When the application is totally dried, then on exposure to air, carbonation it sets slowly but increases in strength steadily as time passes. One week curing is required after complete drying of the applied coat, i.e. after 12 hours.

Coating thickness: The coating thickness should be <=1 mm.

Coverage: Approximately 600 sft / coat / 20 kg “SURYA PLASTO PUTTY” interior.

Colour & Appearance: Milky white & smooth marble like finish.

Packing: Available in 20 kg and 40 kg HDPE bag packing.

Shelf life: 6 months from date of manufacturing, when stored in a cool and dry place.

Advantages:    
- No need to add cement to it.
- Wide spread coverage and brighter.
- No soaking & no primer coats are required.
- Can be easily applied on semi wet or dry cement surfaces.    

Product

Our commitment to quality prompts us to establish a R & D Laboratory - Vijaya Laboratory under technical guidance from National Council for Cement and Building Materials (N.C.B.) New Delhi.

Read More...

Other Side

Other Side

Physically, mentally and
behaviorally challenged, minimally or totally dependent...

Read More...

Contact Us

Title
First Name* :
Telephone Number* :
Email* :
Company Name* :
Your Message :